Announcement

Collapse
No announcement yet.

Syringes???

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Syringes???

    I am going to be pinning Test-E and I've got a bunch of 1cc 23g 1.5" laying around. Will these work or do I need 3cc syringes?? If so, can I use a 25g needle for Test-E injections?? I've seen a couple of other places where people use 25g and just heat the oil.....

    What is your opinion?

  • #2
    i personally prefer 3 cc syringes, and i also use 25 gauge with no issues
    Pain is just weakness leaving the body

    Comment


    • #3
      how easy an oil goes through a 25g will depend on how thin the oil is. if you're using GP, you'll be fine.
      if you are new to the board, please take a minute to read the rules...CLICK HERE

      Comment


      • #4
        Yep..it will be Gp

        Comment


        • #5
          Go big or go home use 23g 1' or 1.5' depending on injection area. You will never have to question if the gear will go through a 23g!!!! I wouldn't ever use anything else but that just me!

          Comment


          • #6
            Originally posted by sam1976 View Post
            how easy an oil goes through a 25g will depend on how thin the oil is. if you're using GP, you'll be fine.
            I agree. I had not problems with sust but it was hard gettin deca through a 25g. Depends on the oil. You will need a minimum of 23g to draw tho. I use 21g to draw or it takes forever.

            Comment


            • #7
              I always use 23g as well.Just much easier.I also use the same to draw and poke though.I never had any bad luck with this so I never saw the need to switch pins.I know many many do,but just not my thing and its worked well so I have stuck with it.

              Comment


              • #8
                I have 18g to draw and some 23g to pin....my main concern is the 1cc syringes I have on hand.....

                Comment


                • #9
                  3cc's are the way to go.Enough room to draw the gear and airate properly.The 1cc will work,but imo it will be much easier with the 3.

                  Comment


                  • #10
                    I get the 3cc with the 20's already attached and draw with those, then screw on a new 25g If its thick, then I just load up and set it on top of my coffee pot while brewing.
                    It's just a small setback in a forward motion

                    Comment


                    • #11
                      Originally posted by Chuck40 View Post
                      I get the 3cc with the 20's already attached and draw with those, then screw on a new 25g If its thick, then I just load up and set it on top of my coffee pot while brewing.
                      Or just use a 23g and u won't have to warm the gear. This is a no brainier to me!!! Also, I agree 3cc are the way to go best all around!!! I myself draw from an amp using 18g and from a muti vial I use 21g because 18 is to big in my opinion and just chews up the rubber stopper.
                      football09
                      Member
                      Last edited by football09; 04-29-2011, 01:44 AM.

                      Comment


                      • #12
                        I don,t know if it,s just me ,but i ,v tried the 23g and find that the glute self injections can take some pretty hard pressure applied to the plunger to get the oil based products injected and in some instances the extra pressure being applied to the plunger causes the needle to move and depress even further into the glute tissue. Thus at times causeing me to hit a vein. Don,t get me wrong when i pin my quad i always go with a 23g,because your in a straight forward position to apply extra pressure without having the needle tip move and rip through your ass muscle tissue. Also when i started out and resarched the self injection methods. tHEY ALL PRETTY MUCH STATED TO USE 22G tips when injecting into glutes. It,s funny how there is so much conflicting information out there.

                        Comment


                        • #13
                          It depends in the oil. Gp stuff is so thin, I noticed no real difference between 25g and 23g. British Dragon stuff was very thick and required a good amount of pressure to het threw a 23g.

                          Comment


                          • #14
                            All good info guys..... Still waiting on my goodies though

                            Comment

                            Working...
                            X